Drive Precision Nails With a Palm Nailer
For the most part the nailing tool of choice is the nail gun, a heavy duty tool that is capable of driving nails in at a rapid rate.
When there is a lot of construction going on involving the joining of wood frames or decks, the nail gun is going to be your primary tool.
But there are times when the location of the nail is in an awkward spot making it unsuitable for a nail gun and, sometimes, also virtually impossible to swing a hammer effectively.
This is when a palm nailer is a necessary little tool.
Unlike the nail gun there is no trigger to fire when operating palm nailers.
Instead the nail is hammered into place by pressing the nailer downward onto the head of the nail.
This means that it is a safer tool that can't cause injury from accidental misfires.
The only thing you have to be careful of is that you have properly positioned your nail before you press down or you will be nailing where you don't intend nails to go all the time.
The palm nailer is a pneumatic tool and is connected to an air compressor to provide the power to operate the hammering mechanism.
You can buy different sized palm nailers from the very small such as the Grip-Rite GRTMP16 Mini Air Nailer to the more heavy duty models such as the DeWalt D5180 Heavy Duty Palm Nailer.
Both are capable nailers but the DeWalt has a little more power and will drive nails in at a quicker rate, however both will also give you plenty of performance at a cost that is very reasonable.
Where palm nailers falls down when judged against the nail gun is the speed with which multiple nails may be driven.
One of the main features of the nail gun is that they can be loaded up with a coil of nails that are then fired off in rapid succession if required.
This is a tool that can only handle a single nail at a time before the next one is positioned and driven in and this is why the main use of the of tool is not for large scale jobs but for the smaller areas that cannot be reached by your main nail gun or hammer.
The palm nailer allows for precision nailing in difficult to reach places.
The lightness of the nailer itself means that it can be comfortably held in one hand for extended periods of time without the operator growing weary.
The power of the average palm nailer is generated by an air compressor and will use anywhere between 50 to 125 psi of pressure, hitting the head of the nail at the rate of 1000 to 2000 times per minute.
When there is a lot of construction going on involving the joining of wood frames or decks, the nail gun is going to be your primary tool.
But there are times when the location of the nail is in an awkward spot making it unsuitable for a nail gun and, sometimes, also virtually impossible to swing a hammer effectively.
This is when a palm nailer is a necessary little tool.
Unlike the nail gun there is no trigger to fire when operating palm nailers.
Instead the nail is hammered into place by pressing the nailer downward onto the head of the nail.
This means that it is a safer tool that can't cause injury from accidental misfires.
The only thing you have to be careful of is that you have properly positioned your nail before you press down or you will be nailing where you don't intend nails to go all the time.
The palm nailer is a pneumatic tool and is connected to an air compressor to provide the power to operate the hammering mechanism.
You can buy different sized palm nailers from the very small such as the Grip-Rite GRTMP16 Mini Air Nailer to the more heavy duty models such as the DeWalt D5180 Heavy Duty Palm Nailer.
Both are capable nailers but the DeWalt has a little more power and will drive nails in at a quicker rate, however both will also give you plenty of performance at a cost that is very reasonable.
Where palm nailers falls down when judged against the nail gun is the speed with which multiple nails may be driven.
One of the main features of the nail gun is that they can be loaded up with a coil of nails that are then fired off in rapid succession if required.
This is a tool that can only handle a single nail at a time before the next one is positioned and driven in and this is why the main use of the of tool is not for large scale jobs but for the smaller areas that cannot be reached by your main nail gun or hammer.
The palm nailer allows for precision nailing in difficult to reach places.
The lightness of the nailer itself means that it can be comfortably held in one hand for extended periods of time without the operator growing weary.
The power of the average palm nailer is generated by an air compressor and will use anywhere between 50 to 125 psi of pressure, hitting the head of the nail at the rate of 1000 to 2000 times per minute.
Source...